Bootloaders 

GRUB 2 

GRUB stands for the GRand Unified Bootloader. It was designed to be cross platform compatible with most operating systems including BSD, Linux, and Windows variants. [7]

GRUB must be installed onto the start of the entire drive, not a partition, to avoid issues in the case of partitions needing to be modified. The first 512 bytes of a drive are used for the Master Boot Record (MBR). If you are using a GPT partition then it uses the first 2048 bytes. GRUB will add it’s own data right after that. It is usually a safe and recommended option to create your first partition 1MB after the start of the drive, especially if GPT is in use.

Install the GRUB 2 packages:

Arch Linux:

$ pacman -S efibootmgr efivar grub os-prober

Debian:

$ apt-get install efibootmgr grub-common grub-efi-amd64-bin grub-efi-amd64-signed grub-gfxpayload-lists grub-pc grub-pc-bin libefiboot1 libefivar1 os-prober shim shim-signed

Fedora:

$ dnf install efibootmgr efi-filesystem grub2-common grub2-efi-x64 grub2-pc grub2-tools grub2-tools-efi grub2-tools-extra grub2-tools-minimal grubby os-prober shim-x64

Install GRUB to a drive (replace “X”) and then generate a boot menu configuration file. This will create the menu file that loads up to the end-user upon boot.

$ sudo grub-install /dev/sdX
$ sudo grub-mkconfig -o /boot/grub/grub.cfg

If any changes are made to GRUB’s settings and/or it’s various scripts, run this command to update the changes. [3]

$ sudo update-grub

Common “grub-install” options:

compress = Compress GRUB-related files. Valid options are:
- no (default), xz, gz, lzo
–modules = List kernel modules that are required for boot. Depending on the end-user’s setup, “lvm”, “raid” (for mdadm), and/or “encrypt” (for LUKS) may be required.
–force = Install despite any warnings.
–recheck = Remove the original /boot/grub/device.map file (if it exists) and then review the current mapping of partitions.
–boot-directory = The directory that the “grub/” folder should exist in. This is typically “/boot”. [4]

Configuration 

Important files:

File	Description
/etc/default/grub	Default GRUB settings.
/etc/grub.d/	A folder with various scripts that make up the grub.cfg. Scripts prefixed with lower numbers are executed first.
/boot/grub/grub.cfg	This is automatically generated using the settings from /etc/default/grub and the scripts in /etc/grub.d/ . Manual changes may get overwritten.

Common options:

/etc/default/grub
- GRUB_DEFAULT = The default menu entry to autoboot into.
  - saved = Boot from the last option selected. This is cached in the /boot/grub/grubenv file.
  - Alternatively, this can either be the number of the “menuentry” section, in order from top to bottom, starting at “0”.
  - Or the menu entry title can be explicitly specified. For example, “CentOS Linux (3.10.0-327.13.1.el7.x86_64) 7 (Core)”.
- GRUB_GFXPAYLOAD_LINUX = The graphics settings to use for the GRUB menu. [14][15]
  - auto = Let GRUB guess the best graphics settings to use.
  - text = Basic GRUB text rendering that works on all hardware.
  - keep = Use advanced graphical rendering that can show themes and images. For unsupported graphics devices, the system will be unbootable.

$ sudo grep ^menuentry /boot/grub2/grub.cfg
menuentry 'CentOS Linux (3.10.0-327.18.2.el7.x86_64) 7 (Core)' --class centos --class gnu-linux --class gnu --class os --unrestricted $menuentry_id_option 'gnulinux-3.10.0-327.18.2.el7.x86_64-advanced-d2e5b723-0055-4157-9197-e7d715937e8b' {
menuentry 'CentOS Linux (3.10.0-327.13.1.el7.x86_64) 7 (Core)' --class centos --class gnu-linux --class gnu --class os --unrestricted $menuentry_id_option 'gnulinux-3.10.0-327.13.1.el7.x86_64-advanced-d2e5b723-0055-4157-9197-e7d715937e8b' {

GRUB_TIMEOUT = Set the timeout (in seconds) before booting into the default menu entry.
GRUB_CMDLINE_LINUX = Append kernel options to the end of the “linux” line. These can later be seen in the operating system in /proc/cmdline. This applies to both the normal and recovery mode options.
GRUB_CMDLINE_LINUX_DEFAULT = The same as the above setting except this option does not affect the recovery kernel options.
GRUB_DISABLE_LINUX_UUID = If set to “true”, devices from /dev/ will be used for specifying the root instead of the UUID. The default is “false” which will use UUIDs.
GRUB_DISABLE_LINUX_PARTUUID = If set to “false”, GPT partition UUIDs will be used instead of Linux partition UUIDs.
GRUB_BACKGROUND = Specify the full path to a custom image for GRUB’s menu background.

[5]

GRUB_PRELOAD_MODULES = Default: part_gpt part_msdos. Additional GRUB modules to load. These may be required for special file systems or boot configurations. [12]
- View all of the UEFI GRUB modules:
```
$ ls -1 /boot/grub/x86_64-efi/*.mod
```
- View all of the legacy BIOS boot GRUB modules:
```
$ ls -1 /boot/grub/i386-pc/*.mod
```

Examples 

These are examples configurations for /etc/default/grub. Use grub-mkconfig -o /boot/grub/grub.cfg to load up the new configurations.

Do not show the GRUB menu on boot:

GRUB_TIMEOUT=0
GRUB_TIMEOUT_STYLE=hidden

Show the consolidated GRUB menu on boot:
```
GRUB_TIMEOUT=5
GRUB_TIMEOUT_STYLE=menu
```

Show everything on the main GRUB menu page on boot:

GRUB_TIMEOUT=5
GRUB_TIMEOUT_STYLE=menu
GRUB_DISABLE_SUBMENU=y

Save the selected boot kernel as the default for the next boot:
```
GRUB_DEFAULT=saved
GRUB_SAVEDEFAULT=true
```

[10]

Support for booting off of any file systems:

GRUB_PRELOAD_MODULES="part_gpt part_msdos affs afs bfs btrfs cbfs ext2 fat fshelp geli hfs hfspluscomp hfsplus http iso9660 luks macbless memdisk minix nilfs2 ntfscomp ntfs pxe reiserfs scsi sfs squash4 tftp usf1_be ufs1 ufs2 xfs zfscrypt zfsinfo zfs"

Support for booting more than one operating system:

GRUB_PRELOAD_MODULES="part_gpt part_msdos multiboot2"

Support for compression (required by some file systems):

GRUB_PRELOAD_MODULES="part_gpt part_msdos hfspluscomp lzopio ntfscomp zstd zxio"

[12]

UEFI Boot Name 

When using the UEFI boot menu provided by the BIOS of a motherboard, each operating system has its own name. It is possible to configure this name by using efibootmgr and then re-generating the GRUB configuration file.

Arch Linux:

$ sudo efibootmgr --create --disk /dev/<DEVICE> --part <EFI_PARTITION_NUMBER> --label "Arch Linux Custom Boot Name" --loader /EFI/BOOT/BOOTX64.efi
$ sudo grub-mkconfig -o /boot/grub/grub.cfg

Fedora:

$ sudo efibootmgr --create --disk /dev/<DEVICE> --part <EFI_PARTITION_NUMBER> --label "Fedora Custom Boot Name" --loader \\EFI\\fedora\\shimx64.efi
$ sudo grub2-mkconfig -o /boot/grub2/grub.cfg

Recovery 

In cases where GRUB fails (because it was installed incorrectly), the end-user is automatically switched into GRUB’s rescue shell.

Common options:

insmod = Load kernel modules.
ls = List partitions and file systems within them.
cat = View file contents.
set = Set a boot option.
unset = Remove a boot option.
boot = Attempt to boot again.
halt = Shutdown the computer.
reboot = Restart the computer.

The rescue prompt will look similar to this.

grub rescue>

Example of using these commands to do a custom rescue boot.

grub rescue> ls
(hd0) (hd0,msdos1)
grub rescue> ls (hd0,1)/boot/
grub/
vmlinuz
initramfs-linux.img
grub rescue> set root=(hd0,1)
grub rescue> linux /boot/vmlinuz root=/dev/sda1
grub rescue> initrd /boot/initramfs-linux.img
grub rescue> boot

Alternatively, you can switch back to the graphical GRUB menu and make changes there.

grub rescue> insmod normal
grub rescue> normal

For recovering from a corrupt GRUB installation, fully change root into the environment from a live CD, USB, or PXE network boot. Then you can modify configuration files and re-install GRUB using the same commands used during the installation.

In this example, /dev/sda2 is the root partition and /dev/sda1 is the boot partition. [6]

$ sudo mount /dev/sda2 /mnt
$ sudo mount /dev/sda1 /mnt/boot
$ sudo mount --bind /dev /mnt/dev
$ sudo mount -t proc proc /mnt/proc
$ sudo mount --bind /run /mnt/run
$ sudo mount -t sysfs sys /mnt/sys
$ chroot /mnt
$ /bin/bash
$ export PATH="$PATH:/sbin:/bin"

If you need to recover GRUB from a chroot that is based on a LVM on the host node, make sure that LVM tools are installed on the guest. This way it can properly see the logical volume as a block device.

Debian:

$ sudo apt-get install lvm2

Fedora:

$ sudo yum install lvm2

USB Installation with Both Legacy BIOS and UEFI Support 

Linux can be installed onto a portable storage device that can boot on both legacy BIOS computers and newer UEFI computers. UEFI requires a GPT partition table which means a legacy MBR partition scheme will not work.

GPT partitions:
1. BIOS GRUB boot partition. This extra space provides more room to store a small core.img file. That file contains GRUB boot and partition table data. This partition is only needed when using a smaller GPT partition table. MBR allocates additional space in the boot sector. [26]
- Size: 1 MiB.
- File system: none.
- Partition flag: bios_grub.
- Mount point: none.
1. EFI partition. This stores the UEFI firmware.
- Size: >= 200 MiB.
- File system: FAT32.
- Partition flags: boot and esp.
- Mount point: /boot/efi/.
1. Linux boot partition. This stores the Linux kernel and boot configuration files (optional).
- Size: 1 GiB.
- File system: ext4.
- Partition flags: none.
- Mount point: /boot/.
GRUB requirements:
- Configure GRUB to use GPT partition UUIDs instead of Linux partition UUIDs. GPT partition UUIDs will not change between different UEFI motherboards. [21][22]
- Install GRUB to the UEFI partition mount. Use the --removable option to set a default UEFI firmware at /boot/efi/EFI/BOOT/BOOTX64.efi. This assumes that only one operating system will be installed on the storage device. [9] Also use the --no-nvram option to avoid modifying UEFI variables on the local motherboard. [20]
- Install GRUB to the block device (not a partition) that will be used for legacy BIOS boot.
- Regenerate the GRUB configuration file.

Firmware requirements:

Install all available linux-firmware related packages.

Arch Linux:

$ sudo pacman -S \
    linux-firmware \
    linux-firmware-bnx2x \
    linux-firmware-liquidio \
    linux-firmware-marvell \
    linux-firmware-mellanox \
    linux-firmware-nfp \
    linux-firmware-qcom \
    linux-firmware-qlogic \
    linux-firmware-whence \
    alsa-firmware \
    sof-firmware
$ yay -S \
    mkinitcpio-firmware \
    linux-firmware-asus \
    linux-firmware-valve

Debian (requires the non-free-firmware repository to be enabled):

$ sudo apt-get install \
    alsa-firmware-loaders \
    bladerf-firmware-fx3 \
    dahdi-firmware-nonfree \
    firmware-amd-graphics \
    firmware-ath9k-htc \
    firmware-atheros \
    firmware-b43-installer \
    firmware-bnx2 \
    firmware-bnx2x \
    firmware-brcm80211 \
    firmware-cavium \
    firmware-intel-sound \
    firmware-ipw2x00 \
    firmware-ivtv \
    firmware-iwlwifi \
    firmware-libertas \
    firmware-linux \
    firmware-linux-free \
    firmware-linux-nonfree \
    firmware-misc-nonfree \
    firmware-myricom \
    firmware-netronome \
    firmware-netxen \
    firmware-qcom-media \
    firmware-qcom-soc \
    firmware-qlogic \
    firmware-realtek \
    firmware-samsung \
    firmware-siano \
    firmware-sof-signed \
    firmware-ti-connectivity \
    firmware-tomu \
    firmware-zd1211 \
    sigrok-firmware-fx2lafw

Fedora:

$ sudo dnf install \
    alsa-firmware \
    alsa-sof-firmware \
    alsa-sof-firmware-debug \
    amd-gpu-firmware \
    arm-trusted-firmware-armv8 \
    atheros-firmware \
    atmel-firmware \
    brcmfmac-firmware \
    cirrus-audio-firmware \
    crystalhd-firmware \
    dvb-firmware \
    hackrf-firmware \
    intel-audio-firmware \
    intel-gpu-firmware \
    intel-vsc-firmware \
    iscan-firmware \
    ivtv-firmware \
    iwlegacy-firmware \
    iwlwifi-dvm-firmware \
    iwlwifi-mvm-firmware \
    libertas-firmware \
    linux-firmware \
    linux-firmware-vendor \
    linux-firmware-whence \
    liquidio-firmware \
    midisport-firmware \
    mlxsw_spectrum-firmware \
    mrvlprestera-firmware \
    mt7xxx-firmware \
    netronome-firmware \
    nvidia-gpu-firmware \
    nxpwireless-firmware \
    qcom-firmware \
    qed-firmware \
    realtek-firmware \
    sigrok-firmware-filesystem \
    sigrok-firmware-fx2lafw \
    sigrok-firmware-nonfree \
    tiwilink-firmware \
    uhd-firmware \
    zd1211-firmware

initramfs requirements to load all kernel modules:
- Arch Linux = Remove “autodetect” from the HOOKS=() section in /etc/mkinitcpio.conf. Then run sudo mkinitcpio -P. [18]
- Debian = Set MODULES=most in /etc/initramfs-tools/initramfs.conf.
- Fedora = Install dracut-config-generic. Then run sudo dracut --regenerate-all --force. [19]
Processor microcode updates for better supporting CPUs:
- Arch Linux = Install amd-ucode intel-ucode.
- Debian = Install amd64-microcode intel-microcode.
- Fedora = Install amd-ucode-firmware microcode_ctl.

Example partition layout:

Number  Start   End  Size    File system     Name    Flags
 1049kB  2097kB  1049kB                  primary  bios_grub
 2097kB  500MB   498MB   fat32           primary  boot, esp
 500MB   8500MB  8000MB  linux-swap(v1)  primary  swap
 8500MB  128GB   120GB   btrfs           primary

Arch Linux and Debian:

# UEFI
$ sudo crudini --ini-options=nospace --set /etc/default/grub "" GRUB_DISABLE_LINUX_UUID true
$ sudo crudini --ini-options=nospace --set /etc/default/grub "" GRUB_DISABLE_LINUX_PARTUUID false
$ sudo grub-install --target=x86_64-efi --efi-directory=/boot/efi --bootloader-id=<OPERATING_SYSTEM_NAME> --removable --no-nvram
# BIOS
$ sudo grub-install --target=i386-pc /dev/<DEVICE>
$ sudo grub-mkconfig -o /boot/grub/grub.cfg

Fedora:

# UEFI
$ sudo crudini --ini-options=nospace --set /etc/default/grub "" GRUB_DISABLE_LINUX_UUID true
$ sudo crudini --ini-options=nospace --set /etc/default/grub "" GRUB_DISABLE_LINUX_PARTUUID false
$ sudo grub2-install --target=x86_64-efi --efi-directory=/boot/efi --bootloader-id=<OPERATING_SYSTEM_NAME> --removable --no-nvram
# BIOS
$ sudo grub2-install --target=i386-pc /dev/<DEVICE>
$ sudo grub2-mkconfig -o /boot/grub2/grub.cfg

Most modern Linux installers will default to installing GRUB with UEFI support. After installation, ensure to run the necessary commands to setup legacy BIOS boot.

[8]

Linux Boot Order 

The default order of the Linux kernels is different for each Linux distribution. It is usually managed in the /etc/grub.d/10_linux file. The sort command can have different arguments given to it to customize this.

Arch Linux:

$ sudo sed -i s'/version_sort\ -r/sort/'g /etc/grub.d/10_linux
$ sudo grub-mkconfig -o /boot/grub/grub.cfg

Debian has no easy sort function to change.

Fedora:

$ sudo sed -i s'/sort\ -Vr/sort/'g /etc/grub.d/10_linux
$ sudo grub2-mkconfig -o /boot/grub2/grub.cfg

Secure Boot 

Secure Boot is an optional feature of Unified Extensible Firmware Interface (UEFI). It is not compatible with legacy BIOS. Most modern computers have this enabled by default and use Microsoft keys to verify the signature of components used for boot. On some Linux distributions such as Debian and Fedora, at least the GRUB bootloader and the Linux kernel are signed. [23]

Self Signing 

It costs thousands of dollars and takes a long time to get into the Microsoft Hardware Partner program which provides a certificate for signing boot components. Instead, users can create and use a Machine Owner Key (MOK) for self signing. [23][24]

Install the mokutil, openssl, and sbsigntools packages on Arch Linux, Debian, or Fedora.

Generate the public (der) and private (priv) keys.

$ sudo mkdir -p /var/lib/shim-signed/mok/
$ cd /var/lib/shim-signed/mok/
$ sudo openssl req -nodes -new -x509 -newkey rsa:2048 -keyout MOK.priv -outform DER -out MOK.der -days 36500 -subj "/CN=<NAME>/"

Create a copy of the public key in the PEM format. mokutil only works with the DER format and sbsign only works with the PEM format.

$ sudo openssl x509 -inform der -in MOK.der -out MOK.pem

Verify that Secure Boot is enabled.

$ sudo mokutil --sb-state
SecureBoot enabled

Import the public key into UEFI. This requires setting a password. On some hardware, this can take longer than the default of 10 seconds so disable the timeout first. [25]

$ sudo mokutil --timeout -1
$ sudo mokutil --import /var/lib/shim-signed/mok/MOK.der
input password:
input password again:

Reboot and the system will automatically boot into the “Perform MOK management” tool. Enroll the key.

Enroll MOK > Continue > Yes > Password: (enter the password) > Reboot

Verify that the key was loaded by UEFI.

$ sudo mokutil --test-key /var/lib/shim-signed/mok/MOK.der
/var/lib/shim-signed/mok/MOK.der is already enrolled

Sign the Linux kernel.

$ export KERNEL_VERSION="$(uname -r)"
$ sudo -E sbsign --key /var/lib/shim-signed/mok/MOK.priv --cert /var/lib/shim-signed/mok/MOK.pem "/boot/vmlinuz-${KERNEL_VERSION}" --output "/boot/vmlinuz-${KERNEL_VERSION}.signed"
$ sudo -E mv "/boot/vmlinuz-${KERNEL_VERSION}" "/boot/vmlinuz-${KERNEL_VERSION}.unsigned"
$ sudo -E mv "/boot/vmlinuz-${KERNEL_VERSION}.signed" "/boot/vmlinuz-${KERNEL_VERSION}"

If using third-party drivers such as nvidia.ko or vboxdrv.ko, those need to also be signed. These are normally located in one of these locations:

/usr/lib/modules/${KERNEL_VERSION}/misc/
/usr/lib/modules/${KERNEL_VERSION}/updates/

If any third-party drivers were signed, the initramfs needs to be re-generated.

Arch Linux:
```
$ sudo mkinitcpio -P
```
Debian:
```
$ sudo update-initramfs -k all -u
```
Fedora:
```
$ sudo dracut --regenerate-all --force
```

Reboot and verify that the signed kernel boots. If not, it will display this message.

error: ../../grub-core/kern/efi/sb.c:182:bad shim signature.
error: ../../grub-core/loader/i386/efi/linux.c:258:you need to load the kernel first.

Troubleshooting 

Errors 

Error after selecting a boot entry in the GRUB menu:

ERROR: device 'UUID=9d4e74d8-8046-4f12-9ac9-624b8f306343' not found. Skipping fsck.
mount: /new_root: can't find UUID=9d4e74d8-8046-4f12-9ac9-624b8f306343.
You are now being dropped into an emergency shell.

Solutions:

Boot from the fallback initramfs instead. This uses a full kernel and extra dependencies compared to the minimal default initramfs.
Ensure that the initramfs has all of the Linux kernel modules that are required for storage devices. Normally this is a missing hardware RAID driver.
Ensure that the UUID for the root device is correct. If not, update /etc/fstab and then rebuild the grub.cfg configuration.
On Arch Linux, ensure both the “block” and “keyboard” hooks are loaded before the “autodetect” hook in the initramfs. [11]

$ sudo vim /etc/mkinitcpio.conf
HOOKS=(base udev keyboard block autodetect modconf resume filesystems fsck)
$ sudo mkinitpcio -p linux

Error from GRUB during boot:

error: sparse file not allowed

Solutions:

This means that GRUB was unable to save information such as which kernel was used to boot into and should be the default next time.

Configure GRUB to not automatically save the last boot option.

$ sudo vim /etc/default/grub
GRUB_DEFAULT=0
GRUB_SAVEDEFAULT=false
$ sudo grub-mkconfig -o /boot/grub/grub.cfg

Add support for the correct file system (including compression, if necessary). Refer to the GRUB 2 - Configuration section for a list of valid GRUB modules.

Syntax:

$ sudo vim /etc/default/grub
GRUB_PRELOAD_MODULES="part_gpt part_msdos <FILE_SYSTEM_MODULE> <COMPRESSION_MODULE>"
$ sudo grub-mkconfig -o /boot/grub/grub.cfg

Example:

$ sudo vim /etc/default/grub
GRUB_PRELOAD_MODULES="part_gpt part_msdos btrfs zstd"
$ sudo grub-mkconfig -o /boot/grub/grub.cfg

[13]

History 

Bibliography 

“GRUB Legacy.” Arch Linux Wiki. January 11, 2017. Accessed February 8, 2017. https://wiki.archlinux.org/index.php/GRUB_Legacy
“GNU GRUB Manual 0.97.” GNU. Accessed February 8, 2017. https://www.gnu.org/software/grub/manual/legacy/grub.html
“GRUB.” Arch Linux Wiki. May 27, 2016. https://wiki.archlinux.org/index.php/GRUB
“GRUB2-INSTALL MAN PAGE.” Mankier. February 26, 2014. https://www.mankier.com/8/grub2-install
“GRUB2/Setup.” Ubuntu Documentation. November 29, 2015. https://help.ubuntu.com/community/Grub2/Setup
“Grub2/Installing.” Ubuntu Documentation. March 6, 2015. https://help.ubuntu.com/community/Grub2/Installing
“GNU GRUB Manual 2.00.” GNU. Accessed June 27, 2016. https://www.gnu.org/software/grub/manual/grub.html
“Is a hybrid Linux USB-Stick for UEFI & legacy BIOS possible?” Super User. March 11, 2018. Accessed June 17, 2020. https://superuser.com/questions/801515/is-a-hybrid-linux-usb-stick-for-uefi-legacy-bios-possible
“GRUB/Tips and tricks.” ArchWiki. April 17, 2021. Accessed May 31, 2021. https://wiki.archlinux.org/title/GRUB/Tips_and_tricks
“Simple configuration handling.” GNU GRUB Manual 2.06. Accessed February 5, 2022. https://www.gnu.org/software/grub/manual/grub/html_node/Simple-configuration.html
“Install Arch Linux on a removable medium.” ArchWiki. July 12, 2021. Accessed July 17, 2021. https://wiki.archlinux.org/title/Install_Arch_Linux_on_a_removable_medium
“Understanding the Various Grub Modules.” Linux.org. March 2, 2015. Accessed February 5, 2022. https://www.linux.org/threads/understanding-the-various-grub-modules.11142/
“GRUB error: sparse file not allowed.” Support - Manjaro Linux. September 6, 2020. Accessed February 2022. https://forum.manjaro.org/t/grub-error-sparse-file-not-allowed/20267/6
“15.1.13 gfxpayload.” GNU GRUB Manual 2.06. Accessed February 16, 2023. https://www.gnu.org/software/grub/manual/grub/html_node/gfxpayload.html
“GRUB gfxpayload blacklist.” Launchpad Ubuntu. Accessed February 16, 2023. https://launchpad.net/ubuntu/xenial/+package/grub-gfxpayload-lists
“Use Linux efibootmgr Command to Manage UEFI Boot Menu.” LinuxBabe. November 13, 2022. Accessed October 4, 2023. https://www.linuxbabe.com/command-line/how-to-use-linux-efibootmgr-examples
“Kickstart overcoming UEFi or converting from MBR.” Light At The End Of The Tunnel. May 10, 2021. Accessed October 4, 2023. https://pkje.net/meander/2016/09/01/kickstart-overcoming-uefi-or-converting-from-mbr/
“mkinitcpio.” Arch Wiki. February 16, 2024. Accessed February 21, 2024. https://wiki.archlinux.org/title/Mkinitcpio
“CentOS 7 - Updates for x86_64: system environment/base: dracut-config-generic.” Linux @ CERN. June 18, 2020. Accessed February 21, 2024. https://linuxsoft.cern.ch/cern/centos/7/updates/x86_64/repoview/dracut-config-generic.html
“What does “–no-nvram” do while installing grub?” Ask Ubuntu. October 7, 2019. Accessed March 28, 2024. https://askubuntu.com/questions/1170347/what-does-no-nvram-do-while-installing-grub
“Arch Linux installed on a portable SSD doesn’t boot on my other machine.” Reddit r/archlinux. January 5, 2024. Accessed March 28, 2024. https://www.reddit.com/r/archlinux/comments/18z64sh/arch_linux_installed_on_a_portable_ssd_doesnt/
“Why do I need GRUB_DISABLE_LINUX_UUID=true.” Unix & Linux Stack Exchange. March 26, 2023. Accessed March 28, 2024. https://unix.stackexchange.com/questions/127658/why-do-i-need-grub-disable-linux-uuid-true
“SecureBoot.” Debian Wiki. January 21, 2024. Accessed April 21, 2024. https://wiki.debian.org/SecureBoot
“Signing a Linux Kernel for Secure Boot.” Ubuntu for Azure Developers. Accessed April 21, 2024. https://gloveboxes.github.io/Ubuntu-for-Azure-Developers/docs/signing-kernel-for-secure-boot.html
“How to change the 10 seconds timeout allotted to enter the “Shim UEFI key management” utility.” Red Hat Customer Portal. September 14, 2023. Accessed April 21, 2024. https://access.redhat.com/solutions/6722091
“GRUB.” ArchWiki. October 23, 2024. Accessed November 9, 2024. https://wiki.archlinux.org/title/GRUB

Bootloaders 

GRUB 1 

Installation 

Recovery 

GRUB 2 

Installation 

Configuration 

Examples 

UEFI Boot Name 

Recovery 

USB Installation with Both Legacy BIOS and UEFI Support 

Linux Boot Order 

Secure Boot 

Self Signing 

Troubleshooting 

Errors 

History 

Bibliography 